Home > Monitors & Gauges > Multi Display Meters > Batman Multi Display System >   Batman Multi Disply Monitor EV 24-144 Volt Systems
	Our Price: $429.95 Product Code: ME-BM-EV-200 Qty:

Description   The BatMan3-EV is a battery monitoring and measuring instrument. It's intended use, is to measure the performance of batteries used in electric vehicle applications. It measures and displays four quantities: 1. Battery current. -750 to +140A. 2. Battery Capacity remaining “Fuel Gauge”. 3. Battery Voltage +20 to +200V. 4. Amp/Hours used since reset. + 999.99 to -999.99Ah. Negative values indicate current out of the battery (discharge), positive values indicate current into the battery (charge). The “Fuel Gauge” will be all black till you have used one eighth of the set capacity. The picture indicates a draw of 124A out of the battery, more than one fourth of the battery capacity has been used, the voltage is around 262V, and 38Amp/Hours have been used so far. In this example, it was set for a capacity of 120 Amp/Hours. Dimensions: 3.26" High by 5.63" Wide x 0.91" Thick, not including the knob. The display characters are 4.84mm(0.2") wide by 9.66mm(0.38") high. Specifications: Current +140A (charge) to 750A +- 1A (discharge). Battery Pack Voltage +20 to +300 +- 0.5V Meter Power: 8 to 80VDC @ 0.025A The BatMan3-EV gives you the information you need to get the most out of the batteries in your electric car. Brochure information: Contents 1. BatMan3-EV measurement and display unit. 2. 10 feet of signal cable, pre-wired, but which can be shortened if necessary. 3. 500A – 50mV current shunt. 4. 12V to 12V isolated DC to DC converter. 5. Six foot RJ-11 cable. 6. RJ-11 to 9-pin RS-232 Serial adapter. 7. Registration Card. 8. This manual. Installation. The BatMan3-EV is connected to the Vehicle through an 8 pin screw terminal connector located on the back of the unit. Current is measured with a 500A=50mV shunt connected between the negative side of the traction pack, and all load connections. With the connector on the left, the pins, from the top, have the following signals: 1. Backlight Negative. 2. Backlight Positive. 3. Internal Backlight Power Positive. 4. Meter Negative (Shunt load side). 5. Shunt Load Side. 6. Shunt Battery Side. 7. Battery Pack Positive. 8. Meter Power (+8 to +80V). Connecting the shunt on the positive side of the battery WILL DAMAGE the unit!

Related Products... Batman Multi Display Monitor EV 24-200 Volt Systems Our Price: $429.95 Add Batman Multi Disply Monitor EV 24-72 Volt Systems Our Price: $379.95 Add Batman EL Multi Display Monitor Our Price: $299.95 Add

 Share your knowledge of this product with other customers... Be the first to write a review.

Browse for more products in the same category as this item: Monitors & Gauges > Multi Display Meters > Batman Multi Display System Monitors & Gauges > Multi Display Meters

	PakTrakr Bus Bar for Current Sensor $5.95
	Controller Kelly 24- 36 Volt 300 Amp Series or PM $219.95
	Conversion Package WarP Impulse Motor, Curtis 72-120V 400A Controller $3,749.95
	Controller Kelly PM 24-72V 300 Amp Reversing & Regen $549.00
	Motor D&D Series 48 VDC 10 Tooth 9.4 hp $395.00
	Contactor ZJW 200 Amps 12 VDC Coils On/Off $69.95
	Controller Kelly 24-144 Volt 650 Amp Programmable Series or PM $1,198.00
	Motor ADC (AMD - Advanced Motors & Drives) 6.7" #L91-4003 72-120VDC 13 HP Double Shaft $889.00
	Motor Netgain WarP 11" TransWarP $3,275.00